Home / Models / JIANGHE / JIANGHE T3007
Editorial illustration of a generic telehandler
Named-model research

JIANGHE T3007

telescopic-boom handler in the manufacturer agricultural application range. Use the load chart to relate capacity to reach; maximum mass and maximum outreach are different conditions.

Reviewed 2026-09-30 · manufacturer claims remain attributed · quotation-specific evidence required

Editorial category illustration; not a photograph, engineering drawing or performance record of this model.

Published scope

Start with the claim, then identify the offered equipment.

The facts below summarize the source reviewed by ForkliftIQ. They do not prove current availability, regional configuration or suitability for a particular site.

Published reference capacity3,200 kg
Published maximum lift / working reach6,700 mm / 3,680 mm, separate source entries
Published forward-extension load entry1,100 kg; exact boom and load-chart condition require confirmation
Published width / height2,100 mm / 2,100 mm
Buyer interpretation

Use the load chart to relate capacity to reach; maximum mass and maximum outreach are different conditions.

A model name helps organize research. Technical approval still depends on one exact configuration and a written operating requirement.

Application boundary

The manufacturer distinguishes the reference load from a lower forward-extension load. These values should not be combined into a promise to carry 3,200 kg at maximum outreach or height. Request the chart for the offered attachment and boom configuration.

Configuration evidence

A telehandler is not a mast forklift. Measure the placement point, reach envelope, approach surface and attachment interface. Ask the responsible supplier to identify the approved conditions for the actual load and site.

Operating-system check

The source narrative and technical table show different travel-speed values. This page does not resolve that conflict by choosing one. Obtain a dated specification and operating limits for the delivered revision.

Information to measure before requesting this model

Draw the load placement point and access route, required height and forward reach, goods dimensions, centre of gravity and attachment. Record surface, gradients, overhead obstructions and ground-support constraints for review.

Request the model-specific chart and instructions rather than using this page as operating guidance. Preserve the boom, attachment, engine and steering identities with the approved quotation. Any attachment substitution needs review of the complete combination.

Questions for the quotation

  • Which chart covers the offered fork carriage and actual load centre?
  • What capacity remains at each required height and reach?
  • Which surface, slope, tyre and steering conditions govern the application?
  • Which dated specification resolves the source travel-speed discrepancy?

Documents to request

Ask for the complete model and option codes, a dated model-specific data sheet, dimensions, the configuration-specific load chart, battery and charger data, attachment approval, tyre specification, operator and maintenance manuals, scheduled service requirements and the applicable destination-market conformity records. The contracting party should identify who commissions the truck, provides training, supports diagnostics, supplies parts and carries warranty responsibility.

How to compare an alternative

Build one comparison sheet and hold the operating case constant. Use the same load, load centre, lift height, attachment, aisle or route, gradients, floor, temperature, shifts and charging window for every candidate. Ask suppliers to show where each quoted value comes from and whether it is standard, optional, calculated, tested or dependent on a market package.

Separate truck price from the operating system around it. Include charger and electrical work, battery replacement assumptions, tyres, scheduled service, diagnostic access, software or telematics fees, training, commissioning, freight, spare parts and expected downtime support. A lower equipment price can produce a higher operational cost when these boundaries are omitted.

Commercial and delivery boundary

Record the legal seller, Incoterm, delivery location, included options, excluded installation work, document language, acceptance method, warranty start, response time and responsible service entity. Require written change control when the supplier substitutes a mast, battery, charger, tyre, controller or software package after the technical review.

Parts and service identity

The family name is not sufficient for a parts match. Preserve the data plate, full model, serial number, mast and attachment details, battery voltage, controller and display labels, old component number, connectors, ports, mounting points and dimensions. Ask the source of every proposed replacement: catalogue record, drawing, supersession notice or written manufacturer confirmation.

Maximum values are not one operating point

A telescopic boom changes the distance between the load and the machine. The reference capacity, greatest lift and longest reach describe different questions. Place the required load and position on the correct chart before comparing models.

Keep the attachment mass and load centre in that calculation. A fork carriage, bucket or another tool can alter the handling case. Require the applicable approved combination and chart rather than accepting a generic capacity statement.

Confirm the offered attachment

List the tool code, mounting interface, hydraulic functions and goods. Ask who supplies approval and instructions for that combination. This profile does not authorize lifting people or using an improvised tool.

Record each required operation separately. A machine that can accept several tools does not have one universal rating for all of them. Keep the delivered attachment identities with the commissioning and future parts records.

Resolve source discrepancies in writing

The source page contains a travel-speed difference between narrative and table. Treat it as a document question. Ask the seller to identify the revision and specify the applicable limit rather than importing either value into a purchasing requirement.

Current engine package and destination records also need confirmation. A public emission reference is a manufacturer statement, not proof that another offered engine satisfies local requirements. Keep the exact engine identity and documents with the quotation.

Plan service around the boom system

Preserve boom, carriage, attachment, cylinder, steering and engine identifiers. Record the component labels and approved instructions before requesting parts. An assembly used on another T-series machine should not be assumed compatible.

Ask who commissions the machine, supports diagnostics and provides replacement components in the destination country. Agree the representative load, placement point and acceptance record with the responsible supplier and site team.

Evidence boundary

ForkliftIQ has not inspected or tested this truck. Published capacity, dimensions, energy and software statements remain attributed to the manufacturer source. Current availability, exact configuration, regional documentation, dealer authority, lead time, field performance and warranty must be confirmed in writing for the offered truck.

Primary manufacturer source reviewedhttps://www.hnjhsv.com/proinfo/3.html
Configuration detail from the source

Transport dimensions and steering choices for the T3007

The manufacturer distinguishes 4,735 mm length without forks from 5,920 mm including forks. Use the appropriate envelope when preparing transport, door and parking requirements. Its table also lists 6,500 kg machine mass and 330 mm ground clearance; obtain the delivered weight, attachment mass and tie-down drawing before arranging freight. Ground clearance alone does not approve a uneven route, ramp transition or approach to a placement point.

The source identifies hydrostatic drive, four-wheel drive and three steering descriptions: two-wheel steering, crab steering and four-wheel steering. Ask the supplier to identify which modes and controls are supplied and provide the instructions governing each operating condition. The published 3,800 mm turning radius is a reference dimension, not an assurance that the machine can negotiate the buyer’s loaded route with an extended attachment.

The engine entries name Kubota and 55.4 kW, with an attributed Euro V emission description. They do not give an exact engine model or prove destination-market approval. Request the engine identification and applicable documents for the actual offer. The source separately describes optional working-monitoring and reversing-camera equipment; include each required item in the option schedule. Preserve the unresolved 35 km/h narrative versus 30 km/h table discrepancy as a written specification question instead of choosing the more favourable figure.

Evidence: JIANGHE T3007 manufacturer source, reviewed 1 October 2026; the full URL is retained in the primary-source section. Published references require confirmation for the exact destination-market configuration.

Compare the exact offer

Start a comparison with this model.

Use the same load, lift height, route and duty requirement when you request alternatives. This model will be preselected in the comparison worksheet; supplier quotation fields remain empty for you to complete.

Open model comparison brief →
Next step

Convert site measurements into one comparable quotation brief.