Sensing components · documented interface
Request a Part Match →Match a forklift sensor using its full reference, measured function, equipment identity and documented output. Distinguish steering, position and process sensors from encoders and mechanical switches. A housing, connector or fault message alone cannot establish the correct replacement.
| Family | Information to retain | Continue research |
|---|---|---|
| Steering or angle sensor | Full reference and steering-system application record | Steering system |
| Position or proximity sensor | Measured target and documented output type | Sensing system |
| Process sensor | Measured variable and exact datasheet | Hydraulic context |
| Motor speed encoder | Encoder identity and feedback requirements | Encoder guide |
| Mechanical limit switch | Actuator and contact configuration | Switch guide |
Begin with the component label and machine parts record. Preserve the supplier or manufacturer name, article number, suffix, revision, truck model and serial number. Record the function that the machine documentation assigns to the sensor. If the label is incomplete, mark the missing information instead of selecting a number from a visually similar listing. A cross-reference should be supported by a traceable document with an identifiable application boundary, not simply a seller assertion.
A steering sensor, proximity sensor and process sensor answer different questions. Ask which variable the installed component measures and which assembly uses that information. Do not infer pressure, position or temperature function from a threaded housing. Record the relevant system and reference drawing. Motor speed feedback belongs in the separate encoder guide, while mechanically actuated contact switches have their own page. These distinctions help a supplier respond to the correct requirement rather than sending a generic sensor quotation.
Request the documented supply, output type, connection designation and any required device or application configuration for the exact proposed reference. A matching connector shell does not establish a matching signal or pin assignment. Retain the source document for each specification. Keep unverified electrical details unknown. This guide does not provide probing, rewiring, calibration or parameter-setting instructions. The responsible technical reviewer should resolve installation suitability using the relevant truck and component documents.
ifm documents IO-Link device identification, hardware and firmware information, process data and parameter features across several sensor families. These examples show why a sensor request may require more than a housing photograph. They do not establish that your forklift uses IO-Link, that all sensors provide these features or that an ifm device replaces an installed truck sensor. Request the actual interface record before discussing configuration. Do not transfer an industrial automation example into a vehicle application without evidence.
Decha lists a Jungheinrich EFB steering sensor under 51869099. Use that supplier-published example as a reference-identification lead, not a universal steering replacement. Another truck still needs its own complete code and serial-range evidence. The company profile is a route for a steering-sensor enquiry; it does not prove coverage of engine sensors, every sensing technology or any particular output. Ask the supplier to identify the exact proposed item and its supporting application document.
Clarify whether the quotation includes a bare sensor, cable, bracket, connector, target element or assembled module. Ask for the drawing, environmental specification, condition, configuration scope, warranty and current delivery basis. Record any included accessories separately so prices remain comparable. A diagnostic code or intermittent reading does not establish that replacing a sensor will resolve the problem. Keep diagnosis separate from procurement, and make unresolved identification or interface differences visible to the technical reviewer.
These company routes are tied to readable manufacturer or company-controlled material reviewed on 3 October 2026. Use the stated scope to begin a shortlist. A profile does not establish current stock, certification, authorisation or a match for your truck.
Its website lists a Jungheinrich EFB steering sensor under reference 51869099. This supports a steering-sensor enquiry route only. It does not establish coverage of every sensor type, an IO-Link installation or a match for another truck.
Website: www.dechaparts.com
Open supplier profile →For additional candidates, use the parts supplier directory. Ask each supplier to return the exact proposed item, condition, included documents, unresolved differences, quantity, destination and current delivery terms. Keep technical acceptance separate from commercial availability.
The current sensor catalogue separates linear-displacement, steering-angle, angle and speed/rotation-angle entries. The reviewed linear-displacement item describes a non-contact Hall sensing approach and applications in joystick lift sensing and valve-gap measurement. Its selectable configurations are not a shared forklift specification. The reviewed angle-sensor body identifies a catalogue item but does not expose a complete interface specification. Ask for the exact proposed reference and current drawing before matching either item. Xiamen Jieou is a vehicle-electronics catalogue route. It does not establish broad process-sensor or motor-encoder coverage. Retain missing interface information rather than treating a catalogue title as a replacement specification.
Company-controlled bodies reviewed on 4 October 2026. Supplier discovery, item origin, current supply and truck-specific acceptance remain separate decisions.
Housing shape is a clue only. Retain the complete code, function and documented interface.
No. The output, connection assignment, configuration and application may differ.
No. The ifm source is a technology example. Your truck documentation must identify its actual interface.
The exact reference, application evidence, output documentation, included accessories, condition and unresolved differences.
The references below support the stated category and identification examples. Manufacturer marketing statements are not treated as independent tests. No model-specific operating values, repair procedures or performance promises are inferred for another machine.
Send the equipment identity, complete component reference, existing drawings or label photos, requested scope, quantity and destination. Mark missing information unknown and ask suppliers to answer the same written requirement.
Prepare a Parts Matching Request →